Melitta C2000 Provozní pokyny Strana 20

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 28
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 19
Operating instruction - pages 9 - 23
a) Electric supply
The c2000 is designed for use with a mains supply with a system
impedance Zmax at the house service connection of max. 0.27
ohms. Make sure that this machine is only operated with a mains
supply which fulfills these requirements. Information about the
system impedance can be obtained from your local electricity sup-
plier.
The distribution voltage must conform with the data indicated on
the type plate. The mains lead must be fuse-protected separately
by the client. The connection should be made by means of a plug
socket secured by a residual current operated device (max. 30
mA). Should a fixed connection be necessary, a switch with at least
3 mm contact break must be provided directly next to the machine
for an all-pole mains cut-off.
b) W
ater supply
A stop valve with backflow suppressor, according to specifications,
is to be installed within easy access. If a water filter is used, this
must be mounted vertically. For safety reasons, the special connec-
ting hoses supplied with the machine may not be shortened during
assembly. The dynamic water pressure must be at least 2.5 bar at
approx. 5 litre/minute. Should the pressure exceed 6 bar, a pres-
sure reducing valve must be inserted between the machine and the
main stop valve.
Before operating the machine for the first time, the water filter must
be activated with at least 20 litres of water at full flow. This process
must be repeated for every new filter cartridge.
c) W
ater outlet
All machines are provided with water outlet muffs and must be
connected with the hoses supplied to a drain pipe with stench trap.
Grounds separator
A grounds separator, on castors or telescopic runners, can be pro-
vided on request. The separator has a capacity of 15 kg (which
would result from approx. 5 kg of ground coffee).
14. Savety precautions and warnings
Keep these operating instructions near the machine, so that
the operator can use the machine correctly at all times.
mind. 650
mind. 600
Water filter
Maximum machine safety is among those product features
which Melitta SystemService places particular emphasis on.
Despite all safety precautions, however, incorrect handling
of any machine can always result in potential risks.
For this reason - in the interest of your safety - we have
compiled the following list of danger warnings.
The machine must not be operated outdoors.
The connection of the machine to the customer’s mains
supply as well as all maintenance and repair work must be
carried out exclusively by the Technical Service staff of
Melitta SystemService.
The pressure vessel contained in the machine corresponds
to category V of the pressure vessel regulations and has
been submitted to a pressure test.
The built-in and tested safety devices must under no cir-
cumstances be repaired, changed or bridged by non-ex-
perts.
These safety devices prevent an excessive increase in
pressure and temperature in the water tank. If the safety
valve is ever opened, the machine must be switched off
immediately. Contact the MELITTA Technical Service and
do not switch the machine on again before the problem has
been rectified.
Caution! Do not put hand into the coffee hopper (10) while
the machine is in operation. There is the danger of trapping!
Caution! There is a danger of scalding within the area of the
coffee outlet (13, 15) and hot water outlet (16).
Melitta SystemService will not be liable for damages arising
from through lack of maintenance, unprofessional work on
the machine or the installation of parts not conforming with
the original construction.
MELITTA SystemService reserves the right to carry out, at
any time and without prior arrangement, any modifications
in the interest of technical progress.
If the machine is to be out of operation for a longer period it
must first be cleaned thoroughly.
Turn off water and electricity supply at the mains (see direc-
tions under „Switching off the machine”, page 14).
In case of freezing temperatures, the machine must be drai-
ned of all water to prevent any damage. Please call
MELITTA’s Technical Service in this case.
According to accident prevention regulation BGV A2 of the
German trade association, the operator is obliged to have
this electrical appliance tested for safety in regular intervals
by an authorized electrician. The time interval between two
inspections for this mounted device is no more than 4 years.
It corresponds to BGV A2 and does not need to be tested
further before its initial operation.
The prescribed inspection can, on request, be carried out
and confirmed by MELITTA’s Technical Service.
15. Warranty terms
We grant a twelve-month warranty for the proper functioning of our
appliances / installations. The warranty period commences on the
day of installation. During this period, any defects arising from faul-
ty materials, defective execution and faulty construction will be
repaired by us or by a company authorized by us, free of charge,
subject to proper use and handling. Any components replaced
become our property. They must be placed at our disposal. Any
damage to the appliances arising as a conse-quence of inadequa-
te maintenance and care will not be covered by us, even during the
warranty period. We do not offer any warranty for defects and faults
in our appliances originating from inexpert repair work or the instal-
lation of spare parts not conforming with the original construction.
Excluded from the warranty are all porcelain and glass components
as well as all components subject to normal wear and tear. These
include, amongst others, seals, valves, taps, heat resistors, varnis-
hes, switches and thermostats. Acknowledgement of warranty
damage only after written report of the Customer Service
Department and inspection at the factory.
22
GB
Zobrazit stránku 19
1 2 ... 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Komentáře k této Příručce

Žádné komentáře